2014-01-18T08:47:00-08:00
853 Wireless LAN board error 1 At startup the wireless LAN board could be accessed, but the wireless LAN board (IEEE 802.11b or Bluetooth...
مزيد من المعلومات »
2014-01-18T08:46:00-08:00
857 USB I/F Error The USB driver is unstable and generated an error. The USB I/F cannot be used. The USB driver can generate three types ...
مزيد من المعلومات »
2014-01-18T08:46:00-08:00
860 HDD error 1 The hard disk connection is not detected because it is defective or has not been formatted • Cable between HDC and HDD lo...
مزيد من المعلومات »
2014-01-18T08:45:00-08:00
866 SD card error 1: Recognition error The SD card in the slot contains illegal program data. • Use only SD cards that contain the correc...
مزيد من المعلومات »
2014-01-18T08:45:00-08:00
874 Delete All error 1: HDD A data error was detected for the HDD/ NVRAM after the Delete All option was used. Note: The source of this e...
مزيد من المعلومات »
2014-01-18T08:44:00-08:00
877 Data Overwrite Security SD card error The 'all delete' function did not execute but the Data Overwrite Security Unit (D362) i...
مزيد من المعلومات »
2014-01-18T08:43:00-08:00
900 Electrical total counter error The total count contains something that is not a number. • NVRAM incorrect type • NVRAM defective • NV...
مزيد من المعلومات »
2014-01-18T08:43:00-08:00
920 Printer Error 1 An internal application error was detected and operation cannot continue. • Software defective • Insufficient memory ...
مزيد من المعلومات »
2014-01-18T08:36:00-08:00
990 Software performance error The software attempted to perform an unexpected operation due to: 1) software bug, 2) incorrect internal p...
مزيد من المعلومات »
2014-01-18T08:35:00-08:00
992 Unexpected Software Error Software encountered an unexpected operation not defined under any SC code. • Software defective • An error...
مزيد من المعلومات »
2014-01-18T08:35:00-08:00
997 Application function selection error Application selected by the operator did not start or end normally due to a software problem. An...
مزيد من المعلومات »
2014-01-18T08:34:00-08:00
641 Engine-Controller Communication Error: Non-Response There was no response to a frame sent from the controller board to the engine. • ...
مزيد من المعلومات »
2014-01-18T08:34:00-08:00
669 EEPROM Communication Error The machine failed to detect a match between the read/write data for the EEPROM on the BCU after 3 attempt...
مزيد من المعلومات »
2014-01-18T08:32:00-08:00
636 OSM User Code File Error The correct "usercode" file could not be found in the root folder of the SD card because the file ...
مزيد من المعلومات »
2014-01-18T08:32:00-08:00
620 Communication A break occurred in the connection between the IPU and ADF • ADF disconnected • ADF defective • IPU harness connection...
مزيد من المعلومات »
2014-01-18T08:30:00-08:00
557 Zero cross waveform signal error The waveform of the zero cross signal was detected out of range. • Electrical noise on the power sup...
مزيد من المعلومات »
2014-01-18T08:29:00-08:00
541 Fusing thermistor open (center) The temperature of the hot roller remained below 0C for 5 sec at the center of the hot roller. • Fusi...
مزيد من المعلومات »
2014-01-18T08:27:00-08:00
500 The machine detected motor lock (motor is not operating correctly) • An obstruction has blocked operation of the main motor • Main mo...
مزيد من المعلومات »
2014-01-18T08:25:00-08:00
401 Transfer roller leak error 1 A transfer roller current leak signal wad detected. (The current feedback signal for the transfer roller...
مزيد من المعلومات »
2014-01-18T08:23:00-08:00
302 Charge level output error The PWM output level was detected higher than 50% after 10 consecutive samplings. • HVPS (High Voltage Powe...
مزيد من المعلومات »
2014-01-18T08:22:00-08:00
202 Polygon motor error 1: ON timeout The polygon mirror motor did not reach the targeted operating speed within 10 sec. after turning on...
مزيد من المعلومات »
2014-01-18T08:21:00-08:00
161 IPU Error The self-diagnostic test detected an error at the IPU at power on, or after the machine returned from energy save mode. • H...
مزيد من المعلومات »
2014-01-18T08:18:00-08:00
144-1 SBU connection error Connection to the SBU could not be confirmed, possibly due to a defect in the BCU detection board • Harness co...
مزيد من المعلومات »
2014-01-18T08:16:00-08:00
144-1 SBU connection error Connection to the SBU could not be confirmed, possibly due to a defect in the BCU detection board • Harness co...
مزيد من المعلومات »
2014-01-18T08:15:00-08:00
143 SBU auto adjust error The machine could not acquire the white or black peak level setting at power on. • Exposure lamp, lamp stabiliz...
مزيد من المعلومات »
2014-01-18T08:14:00-08:00
142 White level correction error White level correction could not be set properly during automatic adjustment. • Harnesses at SBU, IPU, B...
مزيد من المعلومات »
2014-01-18T08:14:00-08:00
141 Black level correction error Black level correction could not be set properly during automatic adjustment. • Harnesses at the SBU, IP...
مزيد من المعلومات »
2014-01-18T08:13:00-08:00
121 Scanner home position error 1 The scanner HP sensor did not turn on during scanner initialization or copying. • Scanner motor harness...
مزيد من المعلومات »
2014-01-18T08:12:00-08:00
120 Scanner home position error 1 The scanner HP sensor did not turn off during scanner initialization or copying. • Scanner motor harnes...
مزيد من المعلومات »
2014-01-18T08:12:00-08:00
101-2 Exposure lamp error 1 The standard white level setting dropped below the specified range during scanning. • White plate dirty • Spu...
مزيد من المعلومات »
2014-01-18T08:11:00-08:00
Code Symptom Possible Cause 101-1 Exposure lamp error 1 The standard white level could not be set properly when scanning the white plate...
مزيد من المعلومات »